802.11g PCMCIA Module with Antenna Connectors
The SDC-PC10G provides all key Summit hardware and software capabilities in a PCMCIA (PC Card) form factor. The SDC-PC10G is ideal for integration into legacy application specific devices like portable data terminals, portable printers and medical devices. Hardware innovations enable the CF10G module to provide far greater performance and range than WLAN radio modules designed for office and consumer applications while minimizing power consumption and allowing for operation in challenging environments.
Please review the below data sheets for complete device specifications.
|System Interface||16-bit PCMCIA Type II with 68-pin connector|
|Antenna Interface||2 U.FL (Hirose) connectors for antenna diversity|
|Input Power Requirements||3.3 VDC +/- 10%|
|Typical Power Consumption (at maximum transmit power setting)||
|Operating Temperature||-30° to 85°C (-22° to 185°F)|
|Operating Humidity||10 to 90% (non-condensing)|
|Length||85.6 mm (3.3")|
|Width||54 mm (2.13")|
|Thickness||5 mm (0.2")|
|Weight||30g (1.0 oz)|
|Mounting||68 pin connector|
|Media Access Protocol||Carrier sense multiple access with collision avoidance (CSMA/CA)|
|Network Architecture Types||Infrastructure and Ad Hoc|
|Network Standards||802.11b, 802.11d, 802.11e, 802.11g, 802.11i|
|Data Rates Supported||
|Regulatory Domain Support||
|2.4 GHz Frequency Bands||
|2.4 GHz Operating Channels||
|Transmit Power Settings
Maximum transmit power will vary according to individual country regulations. All values nominal, +/-2 dBm
|Typical Receiver Sensitivity||
|Operating Systems Supported||
Note: All ETSI, FCC, IC, and MIC certifications for the SDC-CF10G are applicable to the SDC-PC10G
All specifications are subject to change without notice
From a user's perspective, the SDC-PC10G is a PCMCIA radio module. From a regulatory and certification perspective, the SDC-PC10G is the SDC-CF10G Compact Flash module inserted into the SDC-PC2CF10 Compact Flash to PCMCIA adapter card.
All ETSI, FCC and MIC (formerly TELEC) certifications for the SDC-CF10G are applicable to the SDC-PC10G. Please review the SDC-CF10G certification information page for detailed information on existing certifications and how your organization can leverage them.
Additionally, Summit has secured Wi-Fi Alliance certification for the SDC-PC10G as a "Dependent Product" of the SDC-CF10G.
Summit is a member of the Cisco Compatible Extensions (CCX) program and has a direct license from Cisco for intellectual property relating to the various versions of the CCX specifications. Summit has submitted the SDC-PC10G to an authorized CCX test lab and has been found to be fully compliant with version 4 of the CCX specifications for application specific devices (ASDs). For those host devices which include the SDC-PC10G, the vendor may assert that their device incorporates a Cisco Compatible radio module.
Click HERE for verification of CCX compliance for this product.
Device vendors who are members of the CCX program may also choose to secure CCX compliance for their end device. When incorporating the SDC-PC10G into their product with the above software version, the vendor need not be a direct licensee for Cisco intellectual property. Rather, in this case the device vendor need only submit their SDC-PC10G enabled device for CCX compliance testing to the version 4 test plan for ASDs. By leveraging Summit's "pre-approved" software and by testing to the same plan, the vendor has a greater assurance that their actual testing will result in end device compliance. Summit will provide consultative services to those vendors who choose to pursue CCX compliance for their Summit-equipped devices.
Like all Summit devices, the SDC-PC10G is fully compliant with European Union Directive 2003/95/EC or Reduction of Hazardous Substances (RoHS) as per our Declaration of Compliance.
Summit has received an for the following standards: 802.11a, 802.11b, 802.11g, WPA (both personal and enterprise), and WPA2/802.11i (both personal and enterprise). For those host devices which include the SDC-PC10G, the vendor may assert that their device incorporates a Wi-Fi Certified Embedded Client. The vendor need not be a member of the Wi-Fi Alliance to make this assertion but may not use the "Wi-Fi Certified" logo in conjunction with their device unless they themselves are a Wi-Fi Alliance member.
If the device vendor is a member of the Wi-Fi Alliance, they may have WFA certification transferred to them only if they integrate the already-certified module into their device in a "hands off" manner; in other words, make no changes during integration that would impact the way in which the module operates. Summit will provide consultative services to those vendors who choose to pursue a Wi-Fi Alliance certification for their Summit-equipped devices.
If any additional information or guidance is required, please contact Summit's certification group via email or by telephone at 330.434.7929.